Start Over Date 1945 Collection IUL Moving Image Archive Unit IUL Moving Image Archive

1. Bill Bailey and the four pillars (18:07)

Date:
1945
Summary:
A story of land economy and one man, Bill Bailey of Clarksville, Tennessee, through whose foresight and untiring effort the Four Pillars of Income were established in Montgomery County, Tennessee (...

2. Cutting with carbide tools part 1 : single point (19:25)

Date:
1945
Summary:
Shows how to select the tool for the job; how to set up the job; how to calculate speed, feed, and depth of cut; how to machine on a lathe, using a single-point carbide tool; and how to correct uns...

3. Grinding a V-block (21:16)

Date:
1945
Summary:
Shows how to set up a V-block to grind the ends and the V; how to rough- and finish-grind the ends; how to establish reference points for grinding the V to precision dimensions; and how to check th...

4. Grinding multiple-point carbide tools (19:54)

Date:
1945
Summary:
Shows how to remove blades from inserted-blade type cutter; how to off-hand grind individual teeth; how to reassemble and align cutter blades; how to circle grind; how to surface grind all tooth-re...

5. Grinding single-point carbide tools (25:42)

Date:
1945
Summary:
Shows how to prepare the wheel for grinding; how to semi-finish and finish-grind a dull tool; how to rough-grind a chipped or broken tip; how to grind a newly brazed tool; and how to grind a chip b...

7. Housing in Scotland (14:52)

Date:
1945
Summary:
Shows examples of permanent and temporary houses planned by the Scottish Housing Advisory Committee and based on opinions of service men and women, and factory workers during World War II.

8. Installing Conduit (24:28)

Date:
1945
Summary:
Shows how to plan the job; how to bend electrical metallic tubing; how to install the metallic tubing runs; how to bend rigid conduit; how to install rigid conduit runs; and how to use flexible con...

9. Installing surface metal raceway (21:15)

Date:
1945
Summary:
Shows how to plan the job; how to use molding raceway fittings; how to install a molding raceway run to a ceiling outlet; how to install a run from a ceiling outlet to a wall switch; how to install...

10. Keeping Your Car Fit (11:18)

Date:
1945
Summary:
Explains why a weekly checkup on tires, battery, engine oil, and radiator is necessary; why tires should be crisscrossed; why a car should be lubricated regularly and the engine oil and gear lubric...

12. Mermaid's paradise (09:56)

Date:
1945
Summary:
A study of aqua-sports using underwater photography. Including swimming, synchronized diving,

13. Molding a horizontal cored part (21:54)

Date:
1945
Summary:
Use of a horizontal core, a split pattern, chaplets, and chaplet supports; how to gate a mold for rapid pouring of a thin casting; and how to clean a casting.

14. Molding with a loose pattern (floor) (24:04)

Date:
1945
Summary:
Shows the difference between bench and floor molding, how to face a deep pattern, ram a drag and walk it off, clamp a mold, locate sprues and risers, and tuck the crossbars of a large cope.

15. Molding with a three part flask (34:59)

Date:
1945
Summary:
Shows how to use a deep follow board; the technique of facing, ramming, and venting a deep green sand core; how to use a cheek in a three-part flask; and the purpose and method of step-gating.

18. Repulsion induction motor general overhaul (24:52)

Date:
1945
Summary:
Shows how to check a repulsion-induction motor for electrical and mechanical faults; how to dismantle a repulsion-induction motor; how to clean and plug the commutator; how to turn the commutator; ...

19. Roughing-in non-metallic sheathed cable (24:02)

Date:
1945
Summary:
Shows how to plan the installation of the circuit run, switch run, and wall receptacle run; how to determine the location of required runs; how to install an offset bar hanger and ceiling outlet bo...

20. Sawing a reverse curve and a bevel reverse curve (17:25)

Date:
1945
Summary:
Shows how to select and lay out stock to avoid waste; how to reverse curves to contour lines; how to use the table tilting gage; how to saw a bevel reverse curve; how to prepare a template for a ne...